Complete Dispersal Auction for Standard Rentals26DL

Kohler 23 HP electric start gas engine, 9000 watt continuous generator, cables reels with cable, in excellent condition

1.5 HP 3 phase, with (2) tool boxes full of accessories, new Morse taper tail stock, Morris taper drill bits, flat bottom drill bits, (3) micrometers, (1) digital caliper, extra 4 jaw chuck, face plates, Large selection of cutter and cutter holders, magnetic dial indicators, oil, round stock, this a real complete lathe for the serious machinist, in very nice condition, the motor may have to changed for those who don't have 3 phase power

230 volt single phase, bottle can be exchanged for refill at Parts Stop in Spruce Grove, in very good condition

300-amp (at 60% duty cycle) portable inverter welding power source capable of MIG, TIG, Stick, and Flux-Cored welding. It features Auto-Line technology 208–460V, 1 or 3-phase input, 5–400A output range, and a 14-pin connector for wire feeders and remotes. in good working condition

extra tips and accessories, 115 volt, in excellent condition

with (2) rolls of aluminum wire, fits 212, 251 & 252 mig welders, in excellent condition

3 HP 230 volt single phase motor, with extra mounted 4 inch X 24 inch stroke cylinder

6 inch vise, plate steel top, 37 inch high, real nice heavy welding and fabrication table

110 volt, lubrication tank with pump, part pail of cutting oil, in good working order

with Power fist 110 volt electric winch, in good working order

wired with plugs & light, 4 drawer tool box, (2) bolt bins (1) standard (1) metric with lots of bolts, vice mounted, rubber standing matt

48 inch wide X 93 inch long, lift height 32 inch, 20 inch ramp, transport handle with wheels, good working condition

Kohler CH440 gas engine, hose and wand, in good working order

115 volt, in working order

230 volt 3 phase, (2) wands, qty of hoses, shop built overhead arm, (2) floor washer bars on casters, chimney pipe, on wood pallet, nozzles and miscellaneous parts, Note this machine looks ugly but it works very well, pump just had a service kit put in.

80 gallon tank, 208-230 volt, 3 phase, in working order, was used in the shop on a daily basis

good working order

electric start, 120 volt outlets, excellent condition

(1) extra new blade, case

(1) 1/3 HP power snake with extra bits, (2) hand held snakes

wired for power and lights, 7 drawer tool box with miscellaneous tools

digital display works and is accurate, in good working order

with carrying bag

with (1) barrel & (1) barrel funnel

with (3) barrel & (1) barrel funnel

working unit

tubing flaring kit, valve spring compressor, brake drum caliper, cylinder hones with extra stones, Tack/Dwell meter, unused 2 inch pipe tap, OTC battery load tester, pressure gauge

wired with plugs and light, 29 inch deep, 37 inch high, with folding door tool storage above bench

244 cu ft oxygen bottle is at 900 PSI (just under half full), 150 cu ft acetylene bottle is at 150 PSI, just installed new torch and hoses, bottles can be exchanged at Parts Stop in Spruce Grove

(1) 3/4 inch drive socket set missing ratchet, (1) complete 1 inch drive socket set

(3) Boxes of Soudotec stud removal rod, (2) 11 lb box 1/8 7018 sealed box, (1) 11 lb 3/16 8018 sealed box, (1) stainless steel 3/32 sealed box, (3) Partial boxes of stud extracting rod, (1) part box of 3/32 8018(1) Partial box 1/8 chamfer rod, (1) 20 lb box of 1/8 down hand rod, (1) partial tube of 309 stainless steel rod, (2) partial hard surfacing boxes, (3) miscellaneous rods, qty of hard surfacing rods

196 cc gas engine, (1) 30 amp,120 plug & (4) 15 amp, 120 volt plugs, runs very good used very little

Honda 13 HP gas engine, hose and wand, in good working order

Honda GX200 gas engine, hose and wand, 2700 PSI. 3.3GPM, in good working order

(4) full boxes of 1-1/2 coil nails, (1) 3/4 full box of 1-1/2 inch coil nails

(2) hammers, (3) boxes of nails, (1) extension shoe

hardly used

3/4 inch chuck, vise, 12 speed, oiler can, 110 volt

(1) 20 ton bottle jack, (1) 12 ton bottle jack

Milwaukee heat gun, multi port fuel injector tester, battery and load tester, (2) hammers, (2) engravers, Qty of hand tools

(2) extra unused blades, metal case, in good working order

in working order

Mixed shop tools and miscellaneous items

115 volt, paint filter, 37 inch W, 37 inch D, 90 inch H

comes with 38 mm and 41 mm sockets

parts trays, drain pan, (2) suction guns

(1) 3/4 drive torque wrench, (2) straight edges, (4) M12 impact drivers, (1) M12 flashlight, (5) M12 batteries, (1) M12 Charger, all in working order

Face shield, googles, qty grinding discs, chipping hammers, wire brushes, gouger,(11) square welding magnets, misc welding supplies, steel storage cabinet 36" W, 17" D, 72" H

20" D, 30" W, 42" H

with a variety of crown staples

(1) cord is missing 1 end

(1) green cords is missing (1) end, heavy 6/4 cord is has plug only on one end

with case (1) battery, (1) charger

wheels on wood cabinet, 110 volt battery maintainer, works great

jack in good working order

110 volt, working order

48 inch wide X 24 inch deep X 28 inch high

die handle with cutting dies from 1/4 inch to 3/" pipe thread, qty of unused thread cutter replacement teeth

both work

see pic of gauge 2000 PSI, can be exchanged at Parts Stop in Spruce Grove

1200 PSI on gauge over half full, can be exchanged at Parts Stop in Spruce Grove

25.5 inch X 38 inch rubber covered deck

110 volt

110 volt

with XC3.0 12 volt high capacity battery

with XC3.0 142 volt high capacity battery

with XC3.0 12 volt high capacity battery

25" D, 45" W, 62" H, comes with back peg board and tool drawer

Good condition

(1) Pro-Point 8 inch bench grinder, (1) Power Fist 6 inch bench grinder

(1) 60 inch roller set, (5) pipe clamps, part of pipe bender, lathe steady rest, milling machine vise

(2) Porta-powers with accessories, small hose leak on larger unit

with case

(1) 100 lb, (1) 75 lb, (1) 60 lb

(1) 3 jaw puller, (1) 2 jaw puller, (2) bearing splitter

1-1/16, 1-1/8, 1-5/8, 1-11/16/ 1-3/4, 1-13/16

(5) wood bits

with metal case

(1) large bolt cutter, (1) 36 inch pipe wrench, (1) 24 inch pipe wrench, (1) Ridgid aluminum 24 inch pipe wrench, (1) 18 inch pipe wrench, large adjustable wrench

(1) set 48 inch long X 34 inch high, (1) set 48 inch long X 31 inch high

Bottle is empty

Bottle is empty

15 inch wide X 42 inch long X 38 inch high

pump & miscellaneous other parts missing

Carpet kicker, Pex pipe crimper, nail puller, (2) tubing benders, banding strap crimper

Halogen light, multi port air tank, winch cable guide, shop stand, (3) shop wall brackets, part roll of 1/2 inch pex pipe

3 speed, 110 volt

(2) air hoses, multi port air connector manifold

115 volt, single phase, working condition

in very good condition

Brake bleeder, Jerry can spout parts